Diff all
###WARNING: NO CUSTOM DEFAULTS FOUND###

# version
# Betaflight / STM32F405 (S405) 4.2.4 Oct 20 2020 / 08:18:45 (fbcaf8c50) MSP API: 1.43
###ERROR: diff: NO CONFIG FOUND###
# start the command batch
batch start

# reset configuration to default settings
defaults nosave

board_name MAMBAF405US_I2C
manufacturer_id DIAT
mcu_id 002d00355853500620303758
signature 

# resources
resource BEEPER 1 C13
resource MOTOR 1 A09
resource MOTOR 2 A08
resource MOTOR 3 C09
resource MOTOR 4 C08
resource LED_STRIP 1 B03
resource SERIAL_TX 1 B06
resource SERIAL_TX 2 A02
resource SERIAL_TX 3 B10
resource SERIAL_TX 4 A00
resource SERIAL_TX 5 C12
resource SERIAL_TX 6 C06
resource SERIAL_RX 1 B07
resource SERIAL_RX 2 A03
resource SERIAL_RX 3 B11
resource SERIAL_RX 4 A01
resource SERIAL_RX 5 D02
resource SERIAL_RX 6 C07
resource INVERTER 1 C00
resource I2C_SCL 1 B08
resource I2C_SDA 1 B09
resource LED 1 C15
resource LED 2 C14
resource SPI_SCK 1 A05
resource SPI_SCK 2 B13
resource SPI_SCK 3 C10
resource SPI_MISO 1 A06
resource SPI_MISO 2 B14
resource SPI_MISO 3 C11
resource SPI_MOSI 1 A07
resource SPI_MOSI 2 B15
resource SPI_MOSI 3 B05
resource ADC_BATT 1 C01
resource ADC_RSSI 1 C02
resource ADC_CURR 1 C03
resource PINIO 1 B00
resource FLASH_CS 1 A15
resource OSD_CS 1 B12
resource GYRO_EXTI 1 C04
resource GYRO_CS 1 A04

# timer
timer B09 AF3
# pin B09: TIM11 CH1 (AF3)
timer A09 AF1
# pin A09: TIM1 CH2 (AF1)
timer A08 AF1
# pin A08: TIM1 CH1 (AF1)
timer C09 AF3
# pin C09: TIM8 CH4 (AF3)
timer C08 AF3
# pin C08: TIM8 CH3 (AF3)
timer B08 AF2
# pin B08: TIM4 CH3 (AF2)
timer B03 AF1
# pin B03: TIM2 CH2 (AF1)

# dma
dma ADC 3 0
# ADC 3: DMA2 Stream 0 Channel 2
dma pin A09 0
# pin A09: DMA2 Stream 6 Channel 0
dma pin A08 0
# pin A08: DMA2 Stream 6 Channel 0
dma pin C09 0
# pin C09: DMA2 Stream 7 Channel 7
dma pin C08 0
# pin C08: DMA2 Stream 2 Channel 0
dma pin B08 0
# pin B08: DMA1 Stream 7 Channel 2
dma pin B03 0
# pin B03: DMA1 Stream 6 Channel 3

# feature
feature -RX_PARALLEL_PWM
feature RX_SERIAL
feature TELEMETRY
feature LED_STRIP
feature OSD

# serial
serial 0 64 115200 57600 0 115200
serial 3 1 115200 57600 0 115200

# led
led 0 14,12::C:1
led 1 15,12::C:1
led 2 14,13::C:1
led 3 15,13::C:1
led 4 14,14::C:1
led 5 15,14::C:1
led 6 14,15::C:1
led 7 15,15::C:1

# master
set acc_calibration = -45,19,-4231,1
set mag_hardware = NONE
set baro_bustype = I2C
set baro_i2c_device = 1
set serialrx_provider = SBUS
set adc_device = 3
set blackbox_device = SPIFLASH
set dshot_burst = ON
set motor_pwm_protocol = DSHOT600
set current_meter = ADC
set battery_meter = ADC
set beeper_inversion = ON
set beeper_od = OFF
set osd_displayport_device = MAX7456
set enable_stick_arming = ON
set max7456_spi_bus = 2
set pinio_config = 129,1,1,1
set pinio_box = 0,255,255,255
set flash_spi_bus = 3
set gyro_1_bustype = SPI
set gyro_1_spibus = 1
set gyro_1_sensor_align = CW180
set gyro_1_align_yaw = 1800

profile 0

profile 1

profile 2

# restore original profile selection
profile 0

rateprofile 0

rateprofile 1

rateprofile 2

rateprofile 3

rateprofile 4

rateprofile 5

# restore original rateprofile selection
rateprofile 0

# save configuration
save
#