# 

# diff all

# version
# Betaflight / CRAZYBEEF4FR (C4FR) 3.5.7 Mar 15 2019 / 21:42:20 (e9130527c) MSP API: 1.40

board_name CRAZYBEEF4FR
manufacturer_id 
mcu_id 002100283030510a39383634
signature 

# reset configuration to default settings
defaults nosave

# name
name Mobula6 HD

# resources

# mixer

# servo

# servo mix


# feature
feature -TELEMETRY
feature -ANTI_GRAVITY
feature AIRMODE

# beeper
beeper -ARMED

# beacon
beacon RX_LOST
beacon RX_SET

# map
map TAER1234

# serial
serial 1 2048 115200 57600 0 115200

# led

# color

# mode_color

# aux
aux 0 0 0 1800 2100 0 0
aux 1 1 1 900 1200 0 0
aux 2 35 2 1800 2100 0 0

# adjrange
adjrange 0 0 1 900 1200 12 1 0 0
adjrange 1 1 1 1200 1800 12 1 0 0
adjrange 2 2 1 1800 2100 12 1 0 0

# rxrange

# vtx

# rxfail

# master
set gyro_lowpass2_hz = 0
set rc_smoothing_type = FILTER
set rx_spi_protocol = FRSKY_D
set dshot_idle_value = 1000
set motor_pwm_protocol = DSHOT600
set vbat_max_cell_voltage = 45
set vbat_min_cell_voltage = 29
set vbat_warning_cell_voltage = 30
set ibata_scale = 1175
set yaw_motors_reversed = ON
set small_angle = 180
set deadband = 1
set yaw_deadband = 1
set pid_process_denom = 1
set osd_warn_batt_not_full = OFF
set osd_warn_batt_warning = OFF
set osd_warn_esc_fail = OFF
set osd_warn_core_temp = OFF
set osd_rssi_pos = 2362
set osd_tim_2_pos = 2423
set osd_flymode_pos = 2457
set osd_throttle_pos = 2392
set osd_current_pos = 2336
set osd_mah_drawn_pos = 2368
set osd_craft_name_pos = 2442
set osd_warnings_pos = 2345
set osd_avg_cell_voltage_pos = 2401
set osd_disarmed_pos = 2314
set osd_stat_tim_1 = ON
set osd_stat_max_spd = OFF
set osd_stat_battery = ON
set osd_stat_bbox = OFF
set osd_stat_bb_no = OFF
set vtx_band = 3
set vtx_channel = 2
set vtx_power = 2
set vtx_freq = 5685
set vcd_video_system = NTSC
set frsky_spi_tx_id = 97,27
set frsky_spi_offset = -48
set frsky_spi_bind_hop_data = 4,94,184,39,129,219,74,164,19,109,199,54,144,234,89,179,34,124,214,69,159,14,104,194,49,139,229,84,174,29,119,209,64,154,9,99,189,44,134,224,79,169,24,114,204,59,149,0,0,0

# profile
profile 0

set dterm_lowpass2_hz = 0
set dterm_notch_cutoff = 0
set feedforward_transition = 21
set iterm_relax = RPY
set p_pitch = 80
set i_pitch = 25
set d_pitch = 80
set f_pitch = 100
set p_roll = 80
set i_roll = 25
set d_roll = 80
set f_roll = 100
set p_yaw = 90
set i_yaw = 90
set f_yaw = 100

# profile
profile 1


# profile
profile 2


# restore original profile selection
profile 0

# rateprofile
rateprofile 0

set tpa_rate = 30
set tpa_breakpoint = 1200

# rateprofile
rateprofile 1


# rateprofile
rateprofile 2


# rateprofile
rateprofile 3


# rateprofile
rateprofile 4


# rateprofile
rateprofile 5


# restore original rateprofile selection
rateprofile 0

# save configuration
save
#